550 Semi-Automatic Round Product Label Applicator

• Proven reliability
• Cost effective transition from manual labeling to automatic labeling
• Improves label accuracy and efficiency
• Standard web width up to 5″
• Accurately places labels on round products 3/8″ to 4″ diameter
• Portable and lightweight table top unit
• Label application activated by foot switch

Tech Specifications

  • Dimensions: 20″/51cm W x 30″/76cm L x 26″/66cm H
    Weight: 42lbs/19kg (approx.)
    Electric:  115VAC/60Hz/1 AMPS (max.) or 220VAC/50Hz
    Air:  50 PSIG (max.)/3 CFM
    Labels:  Standard 5″ web width, 10″ O.D. roll with 3″ core
    •Die cut with 1/8″ spacing

 

560 Semi-Automatic Tamp-Down Label Applicator

  • Accurately places labels on tops, sides or bottoms of products with flat or slightly curved surfaces
  • Proven reliability
  • Cost effective transition from manual labeling to automatic labeling
  • Portable and lightweight table top unit
  • Label application activated by foot switch
  • Improves label accuracy and efficiency

Tech Specifications

  • Dimensions: 17″/43cm W x 29″/74cm L x 26″/66cm H
  • Weight:  49lbs/22kg (approx.)
  • Electric: 115VAC/60Hz/1 AMPS (max.) or 220 VAC/50Hz
  • Air:  50 PSIG (max.)/6CFM
  • Labels:  Standard 5″ wide  web width 10″ O.D. roll with 3″ core
  • Die cut with 1/8″ spacing

155 Automatic Print and Apply Label Applicator

The Model 155 incorporates an Allen Bradley PLC for easy menu driven operation and control. No more relays or circuit board problems to worry about. Built to last with only the best components available for maximum versatility and performance.

  • Excepcional Placement Accuracy
  • Tamp-down for recessed label application
  • Cost effective transition from manual labeling to automatic labeling
  • Built for Industrial Environment
  • Flexible Mounting allows labeling from side, top, or bottom
  • Portable and lightweight unit

Tech Specifications

  • Interface: USB, RS232, Ethernet, Parallel and Wireless

    Air Requirements: 3 CFM @ 90 PSIG

    Electric Requirements: 110 VAC 60Hz/5 AMP 220 VAC 50HZ

    Equipment Weight: Applicator & Print Engine Only 75 lbs/36kg (approximate)

    Dimensions: 25″ x 25″ x 19″

390 Automatic Horizontal Wraparound Label Applicator

This portable tabletop approach is uniquely designed for labeling small, difficult to handle, round product such as test tubes, ampoules and vials.  Products are fed into the system horizontally and transported to the labeling station where the product is trapped from three sides for extremely accurate label placement.

Tech Specifications

    • Dimensions: 32″L X 18.5″W X 29.5″H
    • Weight:  96 lbs/43.6kg (approx.)
    • Electric: 115VAC/60Hz/1 AMP (max.)
    • Label:  Standard 4.5″ web width/10″ O.D. roll with 3″ Core

Model 110 Wipe-On Label Applicator

The product is guided to the applicator using a consistent conveyor speed. A product sensor detects the product and starts the label applicator.  The label is dispensed matching the speed of the conveyor. A roller or brush is used to wipe-down the label to ensure proper adhesion.

Tech Specifications

    • Dimensions: 15″/38cm
    • Weight:  29 lbs/13kg (approx.)
    • Electric: 115VAC/60Hz/1 AMPS (max.) or 220VAC/50Hz
    • Air:  N/A
    • Labels:  Standard 4 1/2″ web width 10″ O.D. roll with 3″ core
    • Die cut with 1/8″ spacing

Model 110S Servo Control Label Applicator

Auto Labe now offers the Model 110S Servo Control Label Applicator for exceptional label placement accuracy in mid-range application speeds.  The Model 110S was engineered utilizing the latest technology in servo motor drives for years of trouble free, reliable use. Options for the 110S include an encoder interface for varying line speeds, web monitoring systems, adjustable stands and wide label kits.

Tech Specifications

    • Dimensions: 15″ W x 23″ L x 24″ H
    • Weight: 29lbs/13kg (approx.)
    • Electric:  115VAC/60Hz/5 AMP
    • Air:  n/a

155 Automatic Print and Apply Label Applicator

The Model 155 incorporates an Allen Bradley PLC for easy menu driven operation and control. No more relays or circuit board problems to worry about. Built to last with only the best components available for maximum versatility and performance.

  • Excepcional Placement Accuracy
  • Tamp-down for recessed label application
  • Cost effective transition from manual labeling to automatic labeling
  • Built for Industrial Environment
  • Flexible Mounting allows labeling from side, top, or bottom
  • Portable and lightweight unit

Tech Specifications

    • Interface: USB, RS232, Ethernet, Parallel and WirelessAir Requirements: 3 CFM @ 90 PSIGElectric Requirements: 110 VAC 60Hz/5 AMP 220 VAC 50HZEquipment Weight: Applicator & Print Engine Only 75 lbs/36kg (approximate)Dimensions: 25″ x 25″ x 19″

Model 462 Produce Labeler

Designed specially for high speed sorters and conveyors, the Model 462 overhead produce labeler has the features you need. From its PLC, to its stepper motor drive, to its automatic sizer/sorter interfacing, the Model 462 is state of the art produce labeling. The sturdy all metal frame is tough enough for the most demanding labeling conditions. Labelers are self contained and operate independently of one another. With its rapid labeling speeds, you can label 400+ pieces of produce a minute.

Tech Specifications

    • Dimensions: 5.4″/13.7cm W x 23.4″/59.4cm L x 24.6″/62.5cm H 
    • Weight: 22 lbs/10 kg (approx.)
    • Electric: 115VAC/60Hz/3 AMPS (max.)
    • Labels: 1/2″ X 1/2″ to 1″ X 2″ (max.) 14″ O.D. roll with 3″ core pressure sensitive/die cut
    • Labeling Speed: 400+ per minute

Model 140S Tamp Down Label Applicator

Automatic Stepper Tamp/Blow-On Label Applicator Head

Autolabe’s Automatic Tamp-Down Label  Applicator applies a pressure sensitive label utilizing a positive tamp action to ensure complete label adhesion on the product container or package.  Tamp heads of different material from hard to spongy allow for product variation or surface differences.  The Tamp-Down Applicator may be used in any direction and a variety of tamp heads are available.

TAMP-DOWN OPERATIONAL SEQUENCE
The product is consistently guided to the applicator and can be moving or stopped at the point of application.  The label is stripped from the web and is held on a tamp head by vacuum.  When the sensor or switch detects the product, the air cylinder extends pressing the label onto the product.

Tech Specifications

    • Dimensions: 17″/43cm
    • Weight:  35 lbs/16kg (approx.)
    • Electric: 115VAC/60Hz/1 AMPS (max.) or 220VAC/50Hz
    • Air:  80 to 100 PSI G/3 CFMAir:  80 to 100 PSI G/3 CFM
    • Labels:  Standard 4 1/2″ web width 10″ O.D. roll with 3″ core
    • Die cut with 1/8″ spacing
    • Labeling Speed:  1250″ continuous web speed per minute

610 Automatic Pressure Sensitive Labeling System

Automatic Stepper Tamp/Blow-On Label Applicator Head

One of our most popular automatic labeling systems for Food Processors, Deli or Bakery Production.  The system can apply a single label around the top, side (closure) and bottom of plastic hinged clam shell containers.  This is highly useful for product identification as well as integrity sealing the product, all at once.

Tech Specifications

    • The unique design of this system offers an oversized applicator and feed wheel assembly for large roll capacity, allowing for extended production runs.  The open center design stages the label perfectly for product contact and a series of wipe down brushes insure maximize label adhesion.

620 Automatic One Side or Round Product Labeling System

Automatic Stepper Tamp/Blow-On Label Applicator Head

Our most popular economical conveyor system is designed for partial or full wraparound labeling of round products and one sided labeling of square or rectangular products.

Tech Specifications

    • 6 ft standard conveyor (other lengths available)
    • Adjustable guide rails
    • Touch screen technology

680 Automatic Front and Back Labeling System

Automatic Stepper Tamp/Blow-On Label Applicator Head

A complete system for front and back labeling of oval, square or rectangular products, standard features include a feed screw assembly, top hold down belt, control panel, power wipe down rollers and two adjustable label applicators.  This system is designed for accurate label placement for many types of containers.